Where is the Rear Main Seal?

#driveyourlife

Having a problem with the rear main seal in your vehicle can be a scary thing, mostly because many of us don’t entirely know what that seal is or does.  We’ve only heard horror stories about friends who had great reliable vehicles that developed a rear main seal leak and suddenly their car was only fit for a junk yard.  Here at BlueDevil we’re hoping to change that myth.

What is a rear main seal?

The rear main seal is a seal in your engine that is very important and usually difficult to reach.  If you pop your hood and start looking around for the rear main seal, you aren’t going to have much luck seeing it.  It is buried deep, usually under a lot of protective covers, wires, hoses and unfortunately, the bell housing of your transmission.  Let’s first break down the name to see what we can learn about the rear main seal.

First, the rear main seal is at the rear of your engine.  This can be confusing today because the rear of the engine isn’t always at the rear of your engine bay.  On a rear wheel or 4 wheel drive vehicle the engine is mounted with its front (the side with all the pulleys and belts) towards the front of the car.  With modern front wheel drive cars, and some all-wheel drive vehicles the engine can be mounted transversely in the vehicle.  This means that the front of the engine can be facing either the passenger or driver’s side of the vehicle.  So the “rear” in rear main seal refers to the seal’s location on your engine, and not necessarily relative to your vehicle.  The rear main seal is always on the opposite the side of your engine as the pulleys and belts.

Rear Main LeakSecond, the rear main seal is a seal for the main crank shaft bearings in your engine.  Since the crank shaft has the piston attached to it, the pulleys with all your accessories connected to it and the flywheel which connects to your transmission on it, it carries all the forces and power your engine creates.  Since the crank shaft has the toughest job, it gets the biggest and best bearings to make sure it can stand up to the work load.  These bearings are called the main bearings in your engine and carry the majority of the stresses on your crank shaft.  The rear main seal is just on the outside of the rear main bearing and it keeps the engine oil from leaking out where your crank shaft exits the engine.

The outside circumference of the rear main seal creates a seal between the engine block and sometimes the oil pan as well.  The inside of the rear main seal creates a seal on the crankshaft where it exits your engine to connect to the transmission.  As the crank shaft spins, it can wear down the rear main seal, especially if a low oil condition exists in the engine, or the vehicle sits for a long time between uses.

How do I fix a leaking rear main seal?

Because of its location in the engine, replacing a rear main seal includes at least removing the transmission from your vehicle, if not completely removing the engine as well.  Removing either the engine or the transmission from your vehicle is a difficult and time consuming job, usually making a rear main seal replacement a very costly project. This is why you hear so many horror stories about the unbelievable costs of fixing a leaking rear main seal.

The good news is that BlueDevil has created a way to seal your rear main seal leak easily without costly maintenance and long projects.  BlueDevil Rear Main Sealer is a specially formulated additive that you add directly to your engine oil.  BlueDevil Rear Main Sealer is not a petroleum distillate, powder, or hazardous chemical so it will not harm your engine in any way and can stay in your engine oil until your next oil change.  Once BlueDevil Rear Main Sealer is in your engine it will revitalize the old seals you have, restoring them to their original size, shape and flexibility, sealing your rear main seal leak – guaranteed!

 

 

BlueDevil Products can be found on Amazon.com or at AutoZone, Advance Auto Parts, O’Reilly Auto Parts, NAPA, and other major auto parts retailers.

43 responses to "Where is the Rear Main Seal?"

43 Comments

  1. George White on April 24, 2014 at 4:44 pm

    Please contact me as I have sent an e-mail to your tech department. Thank you.

    • BlueDevil Pro on April 24, 2014 at 6:09 pm

      Our tech department has responded direct via email.

    • Eric Gleason on October 20, 2015 at 8:11 pm

      Where is the rear main seal at on a 1982 f250 auto with a 400 and do you have to remove the tryanny or the motor or both?

      • BlueDevil Pro on October 31, 2015 at 11:28 am

        Eric,

        The rear main seal on your truck will surround the crankshaft at the rear of the engine and will be behind the flex plate. If you have a 1 piece rear main seal (found on most new 351 motors) you will have to remove the transmission to replace the rear main seal. If your motor has a 2 piece rear main seal (found on older 351 and 460 motors) you should be able to replace it by simply removing the oil pan and the last main bearing cap.

        Thanks for your question!
        -BD Auto Pro

      • Lance on July 10, 2021 at 4:10 pm

        I own a 2000 Ford ranger 4×4 I’ve had a rear main leak for a while I had my mechanic pull the engine and then he had to go back and pull the transmission it still leaks not bad but it’s still leaks I also think at the front of the engine where the pulley is it may have a small leak there he also changed the gasket up front I hate to keep taking it back to Larry I wonder if Blue devil will help me

        • BlueDevil Pro on July 12, 2021 at 8:26 am

          Lance-

          Thank you for asking about your Ford Ranger. Based on your description, we’d recommend using the BlueDevil Oil Stop Leak. BlueDevil Oil Stop Leak is more concentrated and is the universal application that will work for various leaks such as oil pan leaks, rear main leaks, valve cover gasket leaks, etc. Whereas the Rear Main Sealer is less concentrated and specifically formulated exclusively for leaking rear main seals. If you are not 100% sure where the vehicle is leaking or there seem to be multiple leaks then we recommend using BlueDevil Oil Stop Leak. It is not necessary to add both products simultaneously.

          Thank you!

          -BDP

  2. Martin Longest on April 24, 2014 at 7:17 pm

    I have a 2001 Jeep Cherokee with the 4.0 in-line six cylinder engine. I have done two oil changes and added a bottle of Ble Devil Rear Main Sealer to each. After driving the vehicle for longer periods it doesn’t seem to leak, but on short trips it still drips a little on the exhaust manifold (I can smell it) and leaves about a dime size spot overnight on the driveway. My question is would it do any good or better to use “two” bottles possibly to correct the problem? Thank You!

    • BlueDevil Pro on April 24, 2014 at 7:39 pm

      You still only want to use the recommended amount, 1 bottle, with each application. We do not recommend adding 2 bottles at the same time; you would be better off simply retreating it with 1 bottle.

  3. Jason Cheek on October 27, 2014 at 3:15 am

    I wanted to thank blue devil for there commitment and dedication to not only perfecting a great product, but for helping those in need. I have a family of 5 and only one working vehicle – a 2001 Toyota Sienna. With only one income, another vehicle is just not possible at the moment. My rear main seal went out in August 2014 and with almost 200,000 miles, I couldn’t find a mechanic willing to replace my rear main seal. Then, I heard about Blue Devils Rear Main Seal Stop Leak. After two weeks the leak stopped and the Toyota is doing fine. I’m so thankful that for just $15.00 my vehicle is ruuning just fine.

    Sincerely,

    Jason Cheek

  4. Nick Dearagon on April 1, 2015 at 1:00 pm

    Would this product work on a vehicle using synthetic Mobil 1 oil ?

    • BlueDevil Pro on April 1, 2015 at 1:01 pm

      Nick-

      Yes, the BlueDevil Rear Main Sealer can be used with synthetic Mobil 1 oil. It is 100% compatible.

      Thanks!

      -BDP

  5. Brad Loper on August 21, 2015 at 10:52 pm

    Any guidance with your product and a 1999 Toyota 4 Runner – V6?
    My concern is a non standard oil cooling system that utilizes coolant and can become blocked with sealers.

    • BlueDevil Pro on August 25, 2015 at 9:41 am

      Brad-

      The BlueDevil Rear Main Sealer does not thicken or harden so there is no risk at restricting flow or causing any type of clogging. The BlueDevil will react specifically with the rubber seals and gaskets by rejuvenating and slightly expanding them.

      Thank You!

      -BDP

  6. Ronnie McCutcheon on November 7, 2015 at 5:50 pm

    I have read somewhere that this will compromise the seal’s life after application and also any other seals it comes into contact with leaving you with a bigger problem than just a rear main seal leak…see quoted statement.
    “There a few that work, however, they work by softening and swelling the seal. The softened seal doesn’t last very long and the unfortunate side effect is that this happens to all your seals, leaving you with a bigger problem than you started with.”
    Is there any truth to that statement

    • BlueDevil Pro on November 17, 2015 at 12:09 am

      Ronnie,

      Thanks for your question. There is truth to this statement if you use products that contain petroleum distillates. Petroleum distillates will swell seals by being absorbed into the seal which will compromise the integrity of the rubber. BlueDevil products do not sue any petroleum distillates to recondition seals so our product creates a permanent seal.

      Thanks again for your question!
      -BD Auto Pro

  7. Ken on June 6, 2016 at 5:19 pm

    Hello, I strongly believe the real main seal is leaking from an early, rebuilt, 1950’s 8BA Ford Flathead engine. Have you had any experiences with this application? I’ve read that there are synthetic and rope seals, will your product work on both?

    • BlueDevil Pro on June 10, 2016 at 9:55 am

      Ken-

      The BlueDevil Rear Main Sealer would only be intended for the rubber seals. It would not have any effect on rope, cork or any other type of material that may have been used. If it is indeed a rubber seal, and you are not losing oil too quickly, you would be a good candidate for the product. You can expect to see results after about 100-200 miles of driving.

      Thank you!

      -BDP

  8. billy on September 20, 2016 at 7:25 pm

    I put blue devil rear main seal leak was fine in 30 minutes in my 1988 Honda accord, thanks blue devil

  9. Rebecca Malcolm on February 9, 2017 at 3:01 pm

    I have a 2010 Kia Soul. I’m at the shop now and they found a cam seal leak. What’s the difference between that and a main seal?

    • BlueDevil Pro on February 10, 2017 at 10:31 am

      Rebecca-

      Thank you for asking about your Kia Soul. The difference would be in the location of the seal. The cam seal is located by the timing chain cover and the rear main seal would be at the back end of the engine. Feel free to contact us at 888-863-0426 with any other questions.

      thank you!

      -BDP

  10. jennifer on April 1, 2017 at 9:03 pm

    i have a 2008 Chevy Malibu and have a really bad oil leak coming straight off of the oil filter we have tightened the filter numerous times and it keeps coming loose . Could it have something to do with rear seal ?

    • BlueDevil Pro on April 4, 2017 at 9:16 am

      Jennifer-

      Thank you for asking about your Chevy Malibu. Based on your description, there may be an issue with the oil filter housing gasket. We recommend having the oil filter housing gasket replaced to stop the oil loss.

      Thank you!

      -BDP

  11. Ken on April 12, 2017 at 3:24 pm

    Will your product work on front engine seal as well?

    • BlueDevil Pro on April 12, 2017 at 3:44 pm

      Ken-

      Based on your description, we recommend using the BlueDevil Oil Stop Leak (http://store.gobdp.com/oil-stop-leak-49499/) for your front engine seal leak. The BlueDevil Oil Stop Leak is a universal application, and will treat leaking oil pan gaskets, valve cover seals, rear main seals, etc. where as the Rear Main Sealer is specifically formulated for the rear main seal.

      Thank you!

      -BDP

  12. Andre on November 20, 2019 at 6:40 am

    I have a leak on my rear main seal in my hyundai tucson, where do you check the oil level? is it same as the engine oil level?

    • BlueDevil Pro on November 20, 2019 at 9:43 am

      Andre-

      Thank you for asking about your Hyundai Tucson. You can check the oil level on the dipstick. Based on your description, we recommend using the BlueDevil Rear Main Sealer. You should expect to start seeing results after approximately 100-200 miles of driving.

      Thank you!

      -BDP

  13. michael a denardo on December 9, 2019 at 3:41 pm

    Hi, I have 2004 Honda Odyssey. there is a possibility I might have a slow leak in my rear main seal. Is was recommended I get a second opinion on it. Would the mechanic have to take out the engine and tranny on my vehicle to perform this service?
    I just had my oil changed. Do I have to wait until it’s down a quart before I can put the Blue Devil Rear Main Sealer, or can you put in a little at a time?
    Appreciate your feedback.

    thanks, MD

    • BlueDevil Pro on December 10, 2019 at 9:47 am

      MD-

      Thank you for asking about your Honda Odyssey. The best way to prove that you’ve got a rear main seal leak is to check if the engine side of the flexplate or flywheel is oily. If the rear main seal is leaking on your engine it will drip oil onto the flexplate or flywheel and sling oil around the bellhousing. No, you would not have to wait until the oil was down before adding the BlueDevil Rear Main Sealer. If you are low on oil, add the product and top it off with oil to get it to the proper level.

      Thank you!

      -BDP

  14. Will on January 29, 2020 at 7:58 pm

    I have a 2003 GMC Sierra with 240,000 miles. About a month ago I noticed a very small oil leak… 2 drops smaller than golf balls but larger than quarters… after the truck sat in the garage over night. I used Blue Devil Rear Main Sealer as prescribed (8 oz per 6 quarts of oil), drove the truck a couple days, and the leak stopped! I was very pleased. However, after 3 weeks and 800 miles with no apparent leaks, the oil drops have reappeared, the same as before.

    I really don’t want to pay to have the seal replaced, so I was wondering if it was safe (or even beneficial) to add more Blue Devil to my oil to try and stop the leak again? I have not changed the oil since the first time I added the product.

    Obviously I don’t want to do any damage to my engine, but would reapply Blue Devil if it was absolutely safe to do so.

    Thank you.

    • BlueDevil Pro on January 30, 2020 at 8:41 am

      Will-

      Thank you for asking about your GMC Sierra. Based on your description, we recommend using the BlueDevil Oil Stop Leak. BlueDevil Oil Stop Leak is more concentrated and is the universal application that will work for various leaks such as oil pan leaks, rear main leaks, valve cover gasket leaks, etc. Whereas the Rear Main Sealer is less concentrated and specifically formulated exclusively for leaking rear main seals. If you are not 100% sure where the vehicle is leaking or there seem to be multiple leaks then we recommend using BlueDevil Oil Stop Leak.

      Thank you!

      -BDP

  15. Ashley on September 3, 2020 at 12:47 am

    I have a 2005 Dodge magnum that my son drove once and overheated it and ever since I cannot get it to start and stay on and at first I would fill the radiator reservoir and it was draining and then milky chocolate looking oil started spilling out on the ground I later discovered the old from the dip stick was also milk chocolate colored so I drained it and replaced it and it still won’t start it was leaking from the rear of the engine is this the rear main seal and would ur sealer work for this possibly

    • BlueDevil Pro on September 3, 2020 at 8:49 am

      Ashley-

      Thank you for asking about your Dodge Magnum. Based on your description, it sounds as though water/coolant is getting into the engine oil, creating the milky oil you are seeing. Unfortunately, water/coolant getting into the oil would be a tell-tale sign of a blown head gasket. If the oil is then spilling on the ground, you may be leaking an extreme amount of coolant, which is then overfilling the system and the excess is running out. If the vehicle was run for too long with water in the oil, it may have damaged the engine bearings to the point where the engine will no longer crank. This would mean that the engine needs to be replaced.

      Thank you!

      -BDP

  16. Holly Gross on March 14, 2021 at 3:22 pm

    I have a 05 mazda tribute v6 4wheel drive how bad is it to replace the rear main seal

    • BlueDevil Pro on March 15, 2021 at 11:33 am

      Holly-

      Thank you for asking about your Mazda. Replacing the rear main seal is a very labor intensive job, and will typically take about 8 hours to complete. Feel free to contact our technical support line at 888-863-0426 with any other questions.

      Thank you!

      -BDP

  17. Jessica on May 7, 2023 at 11:48 pm

    Would I have to reapply the rear main sealer again after a certain amount of time? My car pulls when I accelerate from ger 1 to 2. I was told at Toyota that the problem was my rear main seal and torque converter…I’m trying to see if this sealer can fix the present issue or if i have to go ahead and get the whole thing fixed.

    • BlueDevil Pro on May 8, 2023 at 9:10 am

      Jessica-

      Once the product seals, it would be a permanent seal, so should only need to use it once. It is not the kind of additive you would need to use with every oil change. Are you losing engine oil, transmission fluid or both? Please contact our technical support line at 888-863-0426 so that we can get a little better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  18. Marcel Papineau on May 12, 2023 at 8:32 am

    I just bought a 2003 Nissan Xterra 4×4 for my son and poured a bunch of money into it on other parts. Finally thinking it was ready and all of a sudden the oils started leaking from what appears to be the rear main seal. The mechanic gave me a crazy $$$ to fix it because he has to drop the transmission. My question is twofold: If I add the Blue Devil – Rear Main Seal, how long does it usually take to see results? If it continues to leak beyond that estimated time, do I need to change the oil and repeat the process until it stops, or would I have to get the rear main seal replaced because it didn’t work?

    • BlueDevil Pro on May 12, 2023 at 9:24 am

      Marcel-

      Typically, it will be around 100-200 miles of driving before you start to see improvement with the BlueDevil Rear Main Sealer. Depending on the size of the leak, it could take up to around 300 miles of driving before you see the full benefit of the product. The answer to your second question would depend on the results from the first application. If you still have somewhat of a leak after 300 miles of driving, simply contact our technical support line at 888-863-0426 for further assistance.

      Thank you!

      -BDP

      • Marcel Papineau on May 12, 2023 at 11:26 am

        Thank you for your quick reply! After consulting 2 mechanics about your product, both don’t recommend adding anything to the engine oil because it will likely clog and cause bigger problems. Is this a new product that they just aren’t familiar with and need to be educated or is there some validity to this and in certain cases this product isn’t safe for the engine? Have you run into any concerns with voiding engine warranties if you add BD products to the oil?

        • BlueDevil Pro on May 15, 2023 at 8:48 am

          Marcel-

          The product would not clog flow or restrict ports whatsoever. It does not harden or thicken in anyway. It works by revitalizing/reconditioning the rubber seal.

          Thank you!

          -BDP

  19. Frederick on May 16, 2023 at 4:45 pm

    I have a 1999 Saab 9-3. I put in the Blue Devil Rear Main Sealer for preventive maintenance. My car has 209,000 miles on it Over a year, I had some work done on my oil pan and was having a problem with the oil light coming on for a few seconds with the warning triangle popping on. I had the issue checked with several mechanics (thinking it might be the oil level sensor – which was changed) with everyone scratching their head. I just put in the Blue Devil yesterday. Today, driving and making right turns, no oil light/triangle! I was wondering if the Blue Devil Raer Main Sealer can also seal other seals in the car? If this continues, I guess it may have been an old gasket seal.

    • BlueDevil Pro on May 17, 2023 at 8:49 am

      Frederick-

      Thank you for asking about your Saab 9-3. The BlueDevil Rear Main Sealer is specifically intended to treat rear main seals. Were you noticing a loss of oil? With that many miles on the vehicle, it’s possible engine sludge/buildup is making its way through the system and affecting the sensors. If the problem persists, you may want to look into having the oil system flushed to remove said engine sludge.

      Thank you!

      -BDP

Leave a Reply





Related Articles

Search Blog

Subscribe

Blog Categories