How to Fix a Cracked Engine Block

#driveyourlife

cracked engine blockSome problems you run into with your car are small problems.  Cracked radiator hoses, blown fuses, or worn brakes are all problems that can leave you stranded but in the end are simple fixes that can get you back on the road quickly and easily.  On the other hand, some problems can make you start to wonder if it’s time to get a new car or at least a new motor for your old car.  These can include blown head gaskets, worn piston rings or a cracked engine block.  These types of problems usually require major overhauls, lots of labor costs and sometimes weeks of downtime for your car.

Today we’re going to talk about a cracked engine block, how it happens and what your options are.  A cracked engine block is such a big deal because of what your engine block is made out of.  Most of the time when metal breaks, the answer is simple: weld it back together!  In the case of your engine block, this, unfortunately, isn’t possible.  Cast Iron has different properties than most carbon steels that make it impossible to weld.  The extreme heat that it takes to weld most metals is enough to cause problems with cast iron and cause the surrounding area to be surprisingly brittle and weak after the weld.

You can get a crack in your engine block a few different ways.  First, engine blocks can crack from excessive heat.  Too much heat will cause enough expansion and contraction on mating surfaces and bolted joints to cause the faces to start cracking.  In just the opposite scenario, very cold weather can cause your engine block to crack as well.  Whether it is from the wrong mix of antifreeze and water, or you simply live in a very cold area, extremely low temperatures in the winter can cause the coolant in your engine to begin to freeze.  Since water expands when it freezes it can push the walls of your engine block out enough to cause them to crack.

cracked engine blockYou may find out that your engine block is crack a few different ways.  First you may notice coolant leaking externally.  If you find drips of coolant with no leaking gaskets, seals or hoses, you may have a cracked engine block.  In this case, make sure it isn’t simply a leaking freeze plug that is causing your leak!  In some cases, you may also have a cracked engine block that is leaking internally.  In this case, you will find coolant in your engine oil which will turn your oil milky white or light brown.  This can be catastrophic for your engine as watery oil is a very bad lubricant and can start to rust and pit vital bearing surfaces in your engine very quickly.  Lastly, it is possible to have a cracked engine block inside your cylinder.  This type of cracked engine block will give the same symptoms of a blown head gasket and can be very difficult to diagnose.

If you have a vehicle with a cracked engine block it can be tempting to simply junk the car or replace the entire engine.  This can be a very expensive process or leave you with a vehicle.  Rather than costly repairs, use BlueDevil Radiator and Block Sealer to seal the crack in your block and keep your car on the road.  Unlike many leak sealers, BlueDevil Radiator and Block Sealer does not contain any fibers or particulates that simply clog the leak.  BlueDevil Radiator and Block Sealer will actually bond to the cast iron block of your vehicle permanently sealing the crack in your block and keeping you on the road.  We’re so confident BlueDevil Radiator and Block Sealer will stop your leak it is backed by our leak seal guarantee!

00205_blocksealer

For more information about BlueDevil Radiator and Block sealer and our guarantee, click here:

When you’re ready to seal your cracked engine block, stop by any of our partnering local auto parts stores today!

  • AutoZone
  • Advance Auto Parts
  • Bennett Auto Supply
  • CarQuest Auto parts
  • NAPA Auto Parts
  • O’Reilly Auto Parts
  • Pep Boys
  • Fast Track
  • Bumper to Bumper Auto Parts Specialists
  • S&E Quick Lube Distributer
  • DYK Automotive

 

Pictures provided by:

cracked_engine_block.jpg – By Saibo – Licensed By Creative Commons Via Wikimedia – Original Link
cracked_engine.jpg By Loeth – Licensed By Creative Commons Via Wikimedia – Original Link

BlueDevil Products can be found on Amazon.com or at AutoZone, Advance Auto Parts, O’Reilly Auto Parts, NAPA, and other major auto parts retailers.

154 responses to "How to Fix a Cracked Engine Block"

154 Comments

  1. Mark on October 19, 2015 at 3:50 pm

    My ddaughter’s suv is leaving alot of smoke from exhaust however She’s not over heating and her oil is Black. ….is that enough info or do you need more?

    • BlueDevil Pro on October 21, 2015 at 11:07 am

      Mark-

      Based on your description, we would recommend using the BlueDevil Head Gasket Sealer. Not knowing specifically where the leak is coming from, the Head Gasket Sealer would treat a wider range of components ie. leaking heater core, leaking freeze plugs, warped/cracked heads, leaking radiator etc. and the BlueDevil Radiator and Block Sealer is specifically formulated for the radiator and the block.

      Thank you!

      -BDP

      • Melvin Mushwalumuki on July 20, 2017 at 8:02 am

        How can I acquire BlueDevil radiator and block sealer. Am a Zambian

        • BlueDevil Pro on July 20, 2017 at 9:11 am

          Melvin-

          Thank you for you interest in the BlueDevil Radiator & Block Sealer. You can order the product directly on our website, http://store.gobdp.com/radiator-block-sealer-00205/. Simply add the item to your cart, enter your billing and shipping information, and complete the order checkout.

          Thank you!

          -BDP

          • Uk on May 7, 2018 at 6:13 pm

            i have a cracked aluminum engine block in my 2013 honda accord,its mixing oil n water in d radiator as well as the engine oil sump. Had the top gasket changed but the problem still persisted. How do i fix this problem? I’m in Nigeria. How do i get this product if it works on aluminum blocks.



          • BlueDevil Pro on May 8, 2018 at 8:36 am

            Uk-

            Thank you for asking about your Honda Accord. The BlueDevil Head Gasket Sealer is only intended for water/coolant leaks. It would stop the loss of water into the oil, unfortunately, it would not stop oil from getting into the radiator. Unfortunately, we do not manufacture a product intended to stop oil from getting into the radiator. A hard part repair may be your best option.

            Thank you!

            -BDP



          • Johnny on May 27, 2022 at 1:32 pm

            I’m having problem on anti freeze coming out of the muffler of my MPV Mazda, at first it over heated and the mechanic replaced the radiator and hoses and thermostat, the engine is shaking a lot. Is the Blue Devil Radiator and Block sealer will work?



          • BlueDevil Pro on May 31, 2022 at 9:08 am

            Johnny-

            Thank you for asking about your Mazda. How quickly are you losing antifreeze? Is the vehicle still overheating? Please contact our technical support line at 888-863-0426 so that we can get a little better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

            Thank you!

            -BDP



      • Robert on June 6, 2021 at 3:34 pm

        What about water in your plugs? I pulled my spark plugs and found water in one of my plugs.

        • BlueDevil Pro on June 7, 2021 at 9:00 am

          Robert-

          Water/coolant getting onto your spark plugs could be the results of warped/cracked heads, cracked block or a head gasket issue. Please contact our technical support line at 888-863-0426 so that we can get a little better understanding of the vehicle’s condition and be able to make and appropriate recommendations.

          Thank you!

          -BDP

    • samuel on November 30, 2018 at 8:44 am

      Hi it’s me samuel sikhwari from cullinan refilwe i ned to fix my block honda luxlin 1995 and engine 1.5

      • BlueDevil Pro on November 30, 2018 at 2:36 pm

        Samuel-

        Thank you for asking about your Honda Luxline. Is the vehicle losing water/coolant? Please contact our technical support line at 888-863-0426 so that we can get a little better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

        Thank you!

        -BDP

    • Joshua Kratochvil on March 12, 2021 at 4:51 pm

      I’m going to try this, the hard freeze we had here in Texas cracked my block in the coolant department on my IROC. Car starts up and runs fine. Just can’t drive due to coolant leaking, don’t want her overhearing

      • BlueDevil Pro on March 15, 2021 at 8:23 am

        Joshua-

        As long as the leak isn’t more than seeping or lightly dripping, you would be a good candidate for the product. Feel free to contact our technical support line at 888-863-0426 with any other questions.

        Thank you!

        -BDP

    • Aaron R. on November 13, 2021 at 7:21 pm

      I have a crack right where the oil pressure sensor goes on the block. Would this stop the oil from leaking out?

      • BlueDevil Pro on November 15, 2021 at 9:27 am

        Aaron-

        The BlueDevil Oil Stop Leak is only intended for rubber seals/gaskets. If the leak is coming from a rubber component, and the leak isn’t more than seeping or lightly dripping, you would be a good candidate for the product.

        Thank you!

        -BDP

  2. Hugo on October 23, 2015 at 6:03 pm

    What/How are the steps to get the warranty?

    • BlueDevil Pro on October 28, 2015 at 9:31 am

      Hugo-

      Please contact our technical support line at 888-863-0426 so that we can assist you in obtaining the warranty on the product.

      Thank you!

      -BDP

      • Manish verma on November 14, 2017 at 10:28 am

        My car’s coolant box got empty within 300 kms or less still after 3 times head gasket repair.They dismantle the engine each time open it and replacing head gasket but still suffers coolant loss.Owner of hyundai verna fluidic 1.6 ltr diesel engine.can u please suggest what is the main issue in head or engine block?

        • BlueDevil Pro on November 15, 2017 at 9:48 am

          Manish-

          Thank you for asking about your Hyundai Verna. Is the shop performing the work sending the heads out to a machine shop to be surfaced? It is very strange that you have had the head gaskets replaced multiple times and are still experiencing a coolant leak. The work the shop did should be under warranty, however, so you may want to bring the vehicle back for a proper diagnosis.

          Thank you!

          -BDP

  3. Jeremy marghalle on November 11, 2015 at 7:59 pm

    I have a cracked cylinder wall on a 4 cylinder engine would that do anything for it?

    • BlueDevil Pro on December 7, 2015 at 3:13 pm

      Jeremy-

      We recommend using BlueDevil Radiator & Block Sealer. As long as the leak isn’t too severe you should have no problem sealing it with the BlueDevil.

      Thank you!

      -BDP

      • Sue on February 22, 2017 at 3:45 pm

        Hi….The mechanic check my Explorer and said it had a cracked block instead of seals. Would this help me? If so, please give me the exact name so I can purchase the correct item.

        • BlueDevil Pro on February 23, 2017 at 9:13 am

          Sue-

          Thank you for asking about your Ford Explorer. Please contact our technical support line at 888-863-0426 so that we can get a better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

          Thank you!

          -BDP

      • Sean McGuire on June 12, 2017 at 8:16 pm

        I noticed that my oil was very milky so I changed it and it looked good for a few days and now it’s milky and watery again . Any suggestions ?

        • BlueDevil Pro on June 13, 2017 at 8:30 am

          Sean-

          From the sounds of it, you are experiencing the symptoms of a blown head gasket. We recommend using the BlueDevil Head Gasket Sealer (http://store.gobdp.com/head-gasket-sealer-38386/) to help seal your leak. You will want to change your oil before and after the BlueDevil process. Feel free to contact our technical support line at 888-863-0426 with any other questions.

          Thank you!

          -BDP

  4. JB Cooper on December 29, 2015 at 10:52 pm

    My diesel has about a 7 inch crack along the side of the block. It leaks about a gallon every 40 miles or so. Can you help me or am I screwed?

    • BlueDevil Pro on January 6, 2016 at 12:40 pm

      JB-

      Due to the size of the crack BlueDevil would be lost to quickly for it to have a chance at sealing the leak. Unfortunately, you may need to have the hard part repair.

      Thank you!

      -BDP

  5. Cynthia Grimmett on January 22, 2016 at 2:36 am

    I have a 4 inch hair line crack at lower engine block that leaks/drips oil slowly. Can it be sealed? If so how do I apply product?Have 1999 Cadillac Eldora Northstar Engine.

    • BlueDevil Pro on January 22, 2016 at 9:47 am

      Cynthia-

      Unfortunately, we do not make any products that are designed to stop oil loss coming from the block. BlueDevil Radiator & Block Sealer is specifically made to stop coolant loss.

      Thank you!

      -BDP

      • Rick on July 14, 2017 at 12:27 pm

        I have a spark plug hole port leaking antifreeze causing a misfire can you help

        • BlueDevil Pro on July 14, 2017 at 2:23 pm

          Rick-

          It sounds like the vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure. In this case we recommend applying BlueDevil Head Gasket Sealer (http://store.gobdp.com/head-gasket-sealer-38386/). To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder getting the misfire reading. Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly.

          Thank you!

          -BDP

      • Michael on December 28, 2017 at 4:04 am

        My Isuzu 250D is also leaking oil through a hair line crack on the exterior of the block….

        How do i resolve this problem?

        • BlueDevil Pro on December 28, 2017 at 11:36 am

          Michael-

          Thank you for asking about your Izuzu 250D. Unfortunately, we do not manufacture a product intended to stop oil leaks from the Block. A hard part repair may be your best option.

          Hope this helps!

          -BDP

      • Afam on June 30, 2018 at 7:18 am

        Pls my car over heated and my machanic promise to rebuild the engine and he is done with the rebuild but there is a leaks from the engine.Pls advise

        • BlueDevil Pro on July 2, 2018 at 9:14 am

          Afam-

          Do you happen to know where the leak is coming from? Please contact our technical support line at 888-863-0426 so that we can get a better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

          Thank you!

          -BDP

    • Veniamin on July 12, 2017 at 1:46 am

      I have i building pressure in atfrize

      • BlueDevil Pro on July 12, 2017 at 8:48 am

        Vaniamin-

        It sounds like the vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure. In this case we recommend applying BlueDevil Head Gasket Sealer (http://store.gobdp.com/head-gasket-sealer-38386/). To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the lowest compression reading. If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull. Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly. Be sure to follow the guidelines for the proper amount of BlueDevil to apply based on your cooling capacity.

        Feel free to contact us at 888-863-0426 with any questions.

        Thank you!

        -BDP

  6. Jean on March 7, 2016 at 10:04 pm

    Dripping antifreeze, 2003 GMC Safari, hubby thought it was water pump, went to change it and antifreeze still is pouring out. it was low on antifreeze a few weeks ago when it was -4 and hubby is wondering if maybe the block cracked because of it. Any advice? Hate to get a new vehicle.

    • BlueDevil Pro on March 10, 2016 at 9:08 am

      Jean-

      Thank you for asking about your GMC Safari. Based on your description, we would recommend using the BlueDevil Head Gasket Sealer (32 oz yellow label), found here: http://store.gobdp.com/head-gasket-sealer-38386/ . As long as the vehicle can maintain idle for 50 minutes, and you are not losing more than about a quart of water/coolant during that 50 minutes, you would be a good candidate for the product.

      Thank you!

      -BDP

  7. Valters on April 21, 2016 at 3:06 pm

    my toyota mr2 3sgte is getting water bubbles in coolant while idling. we replaced the head gasket but that didnt fix problem. probably a crack in head or block. would this product help? how do i use it?

    • BlueDevil Pro on April 22, 2016 at 11:36 am

      Valters-

      It sounds like the vehicle may be getting combustion/exhaust gases blowing into the cooling system and creating pressure. To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the low compression reading. If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull. Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly. Be sure to follow the guidelines for the proper amount to use based on the size of your cooling system.

      Feel free to contact us at 888-863-0426 with any questions.

      Thank you!

      -BDP

  8. Chirisse Price on June 9, 2016 at 11:20 am

    I think I may have a crack in my engine block. It is leaking oil, I read your article on the blue devil…do you think it would work on my cracked engine block. (2004 Ford Explorer)

    • BlueDevil Pro on June 13, 2016 at 9:15 am

      Chirisse-

      Thank you for asking about your Ford Explorer. The BlueDevil Radiator and Block Sealer is only intended for water/coolant leaks. Unfortunately, BlueDevil does not manufacture a product for stopping oil leaks from the block. A hard part repair may be your best option.

      Thank you!

      -BDP

  9. John Lewis on July 23, 2016 at 7:59 pm

    My boat block has a 2 inch block crack from a harsh winter in Colorado. Could I use this product to seal it from the outside of the block?

    • BlueDevil Pro on July 28, 2016 at 9:31 am

      John-

      Thank you for your interest in the product. Unfortunately, the BlueDevil Radiator & Block Sealer is not designed to seal leaks from outside of the block. The product works internally, is attracted to airflow and reacts with heat to form a chemical weld. A hard part repair may be your best option.

      Thank you!

      -BDP

  10. Roy drewis on August 10, 2016 at 8:02 am

    The Farmall 400 blocks are common to cracks. Have a small horizontal crack just below where the dry sleeve sets in block and a also small vertical hair line crack at the bottom of the sleeve bore where it meets with the oil side of the block. These are dry sleeve engine. On another of these blocks I have there is a verticle crack that crosses from the cylinder bore to the valve lifter bore. will this product seal these.

    • BlueDevil Pro on August 12, 2016 at 9:43 am

      Roy-

      Thank you for asking about your Farmall 400. The BlueDevil Radiator and Block Sealer is intended for water/coolant leaks that are seeping or lightly dripping from the block or radiator. Feel free to contact our technical support line at 888-863-0426 with any other questions.

      Thank you!

      -BDP

      • Fran on March 9, 2018 at 7:32 pm

        Have 4 cy Jeep Wrangler 2900 miles on new motor antifreeze going in oil company head ok would blue devil work on this

        • BlueDevil Pro on March 12, 2018 at 9:07 am

          Fran-

          Thank you for asking about your Jeep Wrangler. Based on your description, we recommend using the BlueDevil Head Gasket Sealer (https://store.gobdp.com/head-gasket-sealer-38386/). As long as you are not losing antifreeze too quickly, you would be a good candidate for the product. You would want to change the oil before and after the BlueDevil procedure.

          Thank you!

          -BDP

  11. Terrance Alexander on August 11, 2016 at 9:49 pm

    I took my 2009 Honda CR-V to 2 shops who said that I have a blown head gasket/cracked head.

    The engine does not turn over and start all the way.

    Can I still use your product?

    • BlueDevil Pro on August 12, 2016 at 9:23 am

      Terrance-

      Thank you for asking about your Honda CR-V. Unfortunately, if the vehicle is unable to run/start, you would not be a good candidate for the product. The vehicle would need to be able to idle for a full 50 minutes without overheating or stalling out in order to achieve proper results. A hard part repair may be your best option.

      Thank you!

      -BDP

  12. Chris on August 18, 2016 at 7:31 am

    Hi – we have a 1966 Oldsmobile 98 Cotner Bevington-made hearse in extremely good condition. It has a 425 ci engine. Yesterday, while driving, the engine overheated and blew coolant out through the radiator cap – we think the old radiator cap actually split and that’s how it started. It completely drained the radiator. The radiator cap has a very strong smell, now. Also, now when the engine starts up, there is tons of whitish smoke coming from the exhaust pipe and some white smoke coming from under the hood. We have had, over the years, a slight engine oil drip (we have to keep the garage floor covered) but it has never accumulated to very much. Any hope for us with one of your products? We’ve got her in the auto shop now to see what has happened. I’m afraid it’s a cracked block. Thanks.

    • BlueDevil Pro on August 19, 2016 at 9:18 am

      Chris-

      Thank you for asking about your Oldsmobile. It sounds like the vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure. We would recommend using the BlueDevil Head Gasket Sealer (32 oz. yellow label) found here: http://store.gobdp.com/head-gasket-sealer-38386/ .
      To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the low compression reading. Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly.

      Thank you!

      -BDP

  13. Terrilynne Work on August 27, 2016 at 2:04 pm

    I have a 3 inch crack in cast iron block of my 1998 Durango causing coolant to drip (and occasionally stream) out underneath the vehicle. Is this crack too large for your product to work?

    • BlueDevil Pro on August 30, 2016 at 9:48 am

      Terrilynne-

      Thank you for asking about your Dodge Durango. Based on your description, we recommend using the BlueDevil Radiator & Block Sealer, found here on our website: http://store.gobdp.com/radiator-block-sealer-00205/. The cooling system should be clean and free-flowing for best overall results. Feel free to contact our technical support line at 888-863-0426 with any other questions.

      Thank you!

      -BDP

  14. lovesandhu on September 1, 2016 at 10:12 pm

    Hi i have honda civic 2006. My car loose antifreeze continuously and my car mechanic says that there might be a crack in block. What should i do ????

    • BlueDevil Pro on September 2, 2016 at 11:40 am

      Please contact our tech support team at 888-863-0426 so that we can get an idea of how quickly you are losing coolant. Depending on how large the leak is, we may have a product that we can recommend.

      We can be reached Monday – Friday, 8:00 AM – 5:00 PM EST.

      Thank you!

  15. Colin on September 3, 2016 at 7:10 pm

    I have a 93 6.5 diesel.. there is a 4 inch hairline crack above my glow plugs on passanger side and 3 ” crack by my starter on driver side.. could the block sealant be a temperary fix untill insave up another 700 for another block?

    • BlueDevil Pro on September 7, 2016 at 9:40 am

      Colin-

      Thank you for your question. How quickly are you losing water/coolant? Is the vehicle overheating at all? Please contact our technical support line at 888-863-0426 so that we can get a better idea as to the extent of the leak and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  16. Bryan on September 6, 2016 at 12:04 pm

    I have a 76 oldsmobile 98 it has a leaking freeze plug would blue devil work for me and what product would you recommend

    • BlueDevil Pro on September 7, 2016 at 8:50 am

      Bryan-

      Thank you for asking about your Oldsmobile. As long as you are not losing water/coolant too quickly, you would be a great product for the BlueDevil Head Gasket Sealer. You may use either Head Gasket Sealer.  The “Pour N Go” (16 oz./white label) is a less concentrated formula that does not require the removal of the thermostat or a flush of the cooling system prior to use.  Whereas the “Mechanic Approved” (32 oz./yellow label) requires both the removal of thermostat and a flush before applying the product; the 32 ounce is the more concentrated formula.  
        The product with the yellow label will give you best overall results as long as you can remove the thermostat and flush the system prior to use.  With the use of either product, be sure to follow the guidelines for the proper amount to use.

      Thank you!

      -BDP

  17. Aljoe Williams on September 12, 2016 at 10:44 pm

    I have a 1996 Toyota hiace that is overheating and bubbles comming out of the radiator will your product work for me

    • BlueDevil Pro on September 13, 2016 at 9:24 am

      Aljoe-

      Thank you for asking about your Toyota Hiace. Based on your description, it sounds like the vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure.  This can be confirmed using a “block dye tester”.  If the combustion/exhaust gases are present then we definitely recommend adding BlueDevil Head Gasket Sealer.  To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the low compression reading.  If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull.  Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly.  Be sure to follow the guidelines for the proper amount to use based on the size of your cooling system.

      Thank you!

      -BDP

  18. Jenna on September 18, 2016 at 9:08 am

    I have a Volvo 2004 S60 that is losing coolant and try to fix what I could myself. But had to bring it to the shop & they told me that it probably has a cracked engine. My coolant is the blue coolant and I just wonder if your product will work for my car. Are there any videos on how the product works?

    • BlueDevil Pro on September 27, 2016 at 9:56 am

      Jenna-

      Thank you for asking about your Volvo S60. As long as your vehicle can maintain idle for a full 45 minutes, and you are not losing more than about a quart of water/coolant during that 45 minutes, you would be a great candidate for the BlueDevil Radiator & Block Sealer. You can check out our YouTube for product spotlights and customer demonstrations.

      Thank you!

      -BDP

  19. Andru on October 13, 2016 at 12:36 pm

    Hi can i add anti freeze to the system after i done blue devil prosess

    • BlueDevil Pro on October 13, 2016 at 3:10 pm

      Andru-

      Yes, once you have completed the BlueDevil process, you may drain the system and add new antifreeze to the system. Feel free to contact our technical support line at 888-863-0426 with any other questions.

      Thank you!

      -BDP

  20. Chris on October 15, 2016 at 1:10 am

    Hi have a bmw 97 year 525tds im loosing coolant from the side of my engine block which i have seen has a small crack ,im loosing about a litre of coolant every 10 days what do you recomend.thank you

    • BlueDevil Pro on October 17, 2016 at 9:55 am

      Chris-

      Thank you for asking about your BMW 525tds. Based on your description, you would be a great candidate for the BlueDevil Radiator & Block Sealer http://store.gobdp.com/radiator-block-sealer-00205/. Feel free to contact our technical support line at 888-863-0426 with any other questions.

      Thank you!

      -BDP

  21. Shakeng on November 14, 2016 at 2:41 am

    Good day,

    I have a nissan 1 tonner bakkie, I took the crank shaft, and the engine block for reconditioning, when they come back as I fill in the water into the radiator, the water runs directly in to the oil sump before i even run the engine, can the blue devil product work?

    • BlueDevil Pro on November 16, 2016 at 9:28 am

      Shakeng-

      Thank you for asking about your Nissan 1 Tonner Bakkie. Based on your description, it seems you may be losing water a little too quickly for the product to be successful. It sounds like you would be losing the product just as quickly as you added it. Unfortunately, a hard part repair may be your best option.

      Thank you!

      -BDP

  22. melanie le clus on November 15, 2016 at 6:49 am

    I have a renault kango and after having the cylinder head fixed and replaced it is still leaking oil into the water and I have a creamy brown oil mix in the water container. does this mean that i have a crack in the block or not.

    • BlueDevil Pro on November 16, 2016 at 9:47 am

      Melanie-

      Thank you for asking about your Renault Kango. Based on your desciription, it sounds like you may have a head gasket leak or a cracked block. Unfortunately, BlueDevil does not manufacture a product intended to stop oil leaking into the water. A hard part repair may be your best option.

      Thank you!

      -BDP

      • Siphiwe on November 11, 2020 at 11:01 pm

        Hi I’m driving polo tsi 1.2 I had blown head gasket and replaced it and my car mix oil with water again after replacing it is it a possibility of crack in engine block blue devil can work in aluminum block

        • BlueDevil Pro on November 12, 2020 at 9:15 am

          Siphiwe-

          Thank you for asking about your Volkswagen Polo. Are you getting oil into the radiator mixing with the water or water/coolant getting into the engine oil? BlueDevil is safe and compatible to use on an aluminum block, however, it is not intended to treat oil from getting into the water/coolant. If that is the case, a hard part repair would be your best option.

          Thank you!

          -BDP

  23. Alan on November 22, 2016 at 10:20 am

    Hi my Citroen dispatch is bellowing white smoke out,the diesel specialist says he thinks it’s a cracked head would your product work?

    • BlueDevil Pro on November 22, 2016 at 3:33 pm

      Alan-

      As long as your vehicle can maintain idle for a full 50 minutes, and you are not losing more than about a quart of water/coolant during that 50 minutes, you would be a great candidate for the BlueDevil Head Gasket Sealer http://store.gobdp.com/head-gasket-sealer-38386/. Feel free to contact our technical support line at 888-863-0426 with any other questions.

      Thank you!

      -BDP

  24. katina on December 19, 2016 at 1:32 pm

    i have a 98 plymoth voyager 3.8 but i didnt have enough.antifreeze.in it and the motor has a crack inthe top of it and its getting tempature hot but the radiator water isnt getting hot nor is it blowing hot out the heater what should i do?

    • BlueDevil Pro on December 21, 2016 at 9:19 am

      Katina-

      Thank you for asking about your Plymouth Voyager. It sounds like you may not be getting the proper circulation in the cooling system. We recommend taking the vehicle to a certified ASE mechanic for a “block dye test” to check for possible combustion/exhaust gasses being in the cooling system.
      BlueDevil Head Gasket Sealer will still work if your vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure.  To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the low compression reading.  If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull.  Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly.  Be sure to follow the guidelines for the proper amount to use based on the size of your cooling system.

      Thank you!

      -BDP

  25. Brehon on January 15, 2017 at 7:20 am

    If heat not working in car will product still work

    • BlueDevil Pro on January 16, 2017 at 9:17 am

      Brehon-

      The reason for the direction of putting the heat on, blower to max, is to draw heat from the engine to keep it from overheating during the process. As long as the vehicle is not going to overheat, it would still be applicable to use the product.

      Thank you!

      -BDP

      • Albert Hill on May 6, 2017 at 12:10 pm

        What if the vehicle overheat during the process due the heater not working?

        • BlueDevil Pro on May 8, 2017 at 9:55 am

          Albert-

          In order to get the benefit of using the product, the vehicle must be able to idle for a full 50 minutes. Otherwise, unfortunately, the vehicle would not be a good candidate for the product. Please contact our technical support line at 888-863-0426 so that we can assist you in obtaining the warranty on the product.

          Thank you!

          -BDP

  26. Ronald Sastrillo on January 18, 2017 at 9:22 pm

    Our nissan serena got overheat and heavy smoke come out at the front area of the car where engine is located.
    Engine did stop on its own after overheat.A repair was done on the radiator where water coming out from there
    was stopped already. However, mechanic told that water keep on mixing with engine oil upon engine start , with this,
    a hydrotest was done to check cylinder head and it has no problem. Now, mechanic is suggesting that a engine block crack maybe the reason for the water leak to oil. But it was not yet check if really the engine block has cracked.
    Will your product be applicable on this type of problem? if so,where we can buy ,we are from philippines? how much?

  27. Dukes on February 22, 2017 at 6:09 pm

    Hi, we have a 95 Mercedes C220. The thermostat was removed but when you drive the car for more the 30min the Temperature goes to 90` celc and water coming out of coolant bottle. can your product help. Were in South Africa. Thanks

    • BlueDevil Pro on February 23, 2017 at 9:15 am

      Dukes-

      Thank you for asking about your Mercedes C220. It is possible that you are getting combustion/exhaust gases pumping back into the cooling system.  You can use a “Block Dye Tester” to confirm whether or not that is the case. If that is the case, we recommend using the BlueDevil Head Gasket Sealer (http://store.gobdp.com/head-gasket-sealer-38386/).
      BlueDevil Head Gasket Sealer will still work if your vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure.  To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the low compression reading.  If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull.  Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly.  Be sure to follow the guidelines for the proper amount to use based on the size of your cooling system.

      Thank you!

      -BDP

  28. Troy Brown on April 12, 2017 at 7:38 pm

    I own a 90 Acura Integra, b18a1, 1.8l, 4 cylinder engine. Recently noticed an antifreeze leak and replaced the water pump. I added antifreeze to the radiator to see if there were any leaks after replacing the the tensioner pulley and timing belt. I noticed antifreeze leaking, but from a hairline fracture behind the tensioner pulley. Will the Blue Devil Radiator and Block Sealer fix this?

    • BlueDevil Pro on April 13, 2017 at 10:40 am

      Troy-

      Thank you for asking about your Acura Integara. The BlueDevil Radiator & Block Sealer is specifically formulated for leaks coming from the radiator and block. If the leak is coming from one of these areas, and you are not losing antifreeze too quickly (more than about a quart in a one hour run time), you would be a great candidate for the product.

      Thank you!

      -BDP

  29. Valiant owner on May 14, 2017 at 5:21 pm

    Have a 1964 Valiant with a cracked block near the water jackets. Welders tape has been previously applied and the vehicle does still run fine with some minor water leakage. Will your product work for this?

    • BlueDevil Pro on May 15, 2017 at 9:45 am

      Valiant owner-

      Based on your description, we do recommend using the BlueDevil Radiator & Block Sealer for your Plymouth Valiant. As long as the vehicle will maintain idle for the full 45 minutes, and you are not losing more than about a quart of water/coolant during that 50 minutes, you would be a great candidate for the product.

      Thank you!

      -BDP

  30. Orali Quiroz on July 31, 2017 at 4:56 pm

    I have a Honda Civic 2006. I have an oil leak and my oil went to to my radiator. Would any of your products help me?

    • BlueDevil Pro on August 1, 2017 at 8:45 am

      Orali-

      Thank you for asking about your Honda Civic. Unfortunately, we do not manufacture a product intended to stop oil from getting into the radiator. A hard part repair may be your best option.

      Thank you!

      -BDP

  31. Brian on August 5, 2017 at 1:04 am

    After idling for one hour, there is still a little bit of coolant dribbling out from the radiator (1950 Plymouth with a brass radiator)

    The problem only appears when the engine is hot and radiator has pressure (7lb cap) then dries up when cold. How long should I allow the Blue Devil block and radiator sealer to do its work?

    Thanks

    • BlueDevil Pro on August 8, 2017 at 8:43 am

      Brian-

      Please contact us at 888-863-0426 so that we may discuss your vehicle and the best steps for getting BlueDevil to seal under your specific conditions.

      Thank you!

      -BDP

  32. Clara on October 20, 2017 at 2:34 am

    I have 2006 Honda civic. My mechanic said that coolant is leaking as there was engine block cracked. Do you think that your product can help my car? Honda offered 10 years extended warranty for this problem, but it’s expired now.

    • BlueDevil Pro on October 20, 2017 at 9:52 am

      Clara-

      Thank you for asking about your Honda Civic. Based on your description, we recommend using the BlueDevil Radiator & Block Sealer (http://store.gobdp.com/radiator-block-sealer-00205/). As long as you are not losing water/coolant too quickly, and the vehicle can maintain idle for a full 45 minutes without overheating, you would be a great candidate for the product.

      Thank you!

      -BDP

  33. Ryan on October 24, 2017 at 12:18 am

    I have a 2007 Cadillac Escalade with oil in the coolant and I’m told this is due to a cracked engine block. I hadn’t noticed any engine problems prior to this news. Will your product seal the leak?

    • BlueDevil Pro on October 24, 2017 at 11:57 am

      Ryan-

      Thank you for asking about your Cadillac Escalade. Unfortunately, we do not manufacture a product intended to stop oil from getting into the cooling system. A hard part repair may be your best option.

      Thank you!

      -BDP

  34. Angela on January 20, 2018 at 11:04 pm

    I have a 1979 Chevy that is a rv was told has a crack in block around the starter I drained oil and it was milky brown what do you recommend

    • BlueDevil Pro on January 22, 2018 at 10:11 am

      Angela-

      Thank you for asking about your Chevy RV. Based on your description, we recommend using the BlueDevil Head Gasket Sealer (https://store.gobdp.com/head-gasket-sealer-38386/). You would want to change the oil before and after the BlueDevil process. Feel free to contact our technical support line at 888-863-0426 with any other questions.

      Thank you!

      -BDP

  35. Scott on January 31, 2018 at 4:48 pm

    I have a 1955 Pontiac 287 that has a 3 inch crack under the intake manifold above cylinders 3 and 5. The crack runs horizontal between the lifter bores and the edge of the block. The engine is out of the car and apart but I’m reading many mixed reviews on stitching the wound or externally applied epoxy. I’m concerned about the head bolt bores as the crack would essentially run between where this blind end bottoms out. What would you recommend to repair the crack?

    • BlueDevil Pro on February 1, 2018 at 9:56 am

      Scott-

      Thank you for asking about your Pontiac 287. About how quickly are you losing water/coolant? Please contact our technical support line at 888-863-0426 so that we can get a better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  36. Kelly Lowe on February 4, 2018 at 10:49 pm

    I have a small chip/crack just by the thermostat housing that is causing coolant to leak out. What do you recommend?

    • BlueDevil Pro on February 5, 2018 at 9:30 am

      Kelly-

      How quickly are you losing coolant? Is the vehicle overheating at all? Please contact our technical support line at 888-863-0426 so that we can get a little better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  37. d davis on February 22, 2018 at 9:56 am

    I have a hole about one inch big in the engine block, will any of your products seal this

    • BlueDevil Pro on February 22, 2018 at 11:03 am

      D Davis-

      How quickly are you losing water/coolant? Is the vehicle overheating at all? Please contact our technical support line at 888-863-0426 so that we can get a little better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  38. Zeno man on April 10, 2018 at 1:08 pm

    My engine is knocking and there is and fast oil leak .. it was suggested there was a crack in the engine block ? What do I do ?

    • BlueDevil Pro on April 10, 2018 at 1:10 pm

      Zeno-

      Unfortunately, it sounds like you are losing oil a little to quickly for the BlueDevil Oil Stop Leak to be affective. A hard part repair may be your best option.

      Thank you!

      -BDP

  39. Amber on April 21, 2018 at 7:07 pm

    We have a 99 Ford F-350 7.3 motor. We did have a small crack in the block but we used blue devil and it sealed it, at least I know it sealed it on the outside crack that we could see. Now here is the problem. We are still having issues with the truck over heating, It seems like it is building up pressure and then causing it to have so much pressure that it is pushing the water out the cap of the reservoir. We also just changed the clutch fan because we didn’t notice it turning on when the truck starts getting hot. It still doesn’t seem to be coming on with the new fan clutch. We are running out of ideas. Could there be another crack on the inside of the block?

    • BlueDevil Pro on April 23, 2018 at 9:05 am

      Amber-

      Thank you for asking about your Ford F-350. Are you still noticing a loss of water/coolant? Did you use the Head Gasket Sealer or the Radiator & Block Sealer? Based on your description, it is possible that you are getting combustion/exhaust gases pumping back into the cooling system. You can use a “Block Dye Tester” to confirm whether or not that is the case.
      BlueDevil Head Gasket Sealer will still work if your vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure. To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the low compression reading. If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull. Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly. Be sure to follow the guidelines for the proper amount to use based on the size of your cooling system.

      Thank you!

      -BDP

  40. Gregg Szafran on May 29, 2018 at 2:42 pm

    I have a 1995 Evinrude 90 HP 2 stroke, I had the head gaskets done last year. This spring I had my mechanic do the thermostats and the exhaust gasket. When he removed the back cover he notices there were cracks starting in the lower right side of the head which was starting to score the piston. Will Blue Devil repair those cracks before they get worse? The head is aluminum, I don’t think they make them anymore/

  41. Raymond Dunlap on April 22, 2019 at 3:02 am

    I see it works for cast iron .. But i have an aluminum block that i suspect of being cracked

    Its a turbo’d honda civic
    Not only does lose water but also builds a decent amount of pressure in the coolant hoses

    I replaced the head and head gasket

    It doesnt leak water anywhere externally that i can see … Unless its coming out of the coolant reservoir and im just not noticing

    The main thing im concerned about is the pressure in the radiator hose’s

    Haha back to the question ( does blue devil work on aluminum blocks?

    • BlueDevil Pro on April 22, 2019 at 11:28 am

      Raymond-

      Yes, BlueDevil is compatible and safe to use on aluminum. Based on your description, it is possible that you are getting combustion/exhaust gases pumping back into the cooling system. You can use a “Block Dye Tester” to confirm whether or not that is the case.
      BlueDevil Head Gasket Sealer will still work if your vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure. To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the low compression reading. If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull. Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly. Be sure to follow the guidelines for the proper amount to use based on the size of your cooling system.

      Thank you!

      -BDP

  42. Jack on May 11, 2019 at 8:41 pm

    My 2011 Subaru Forester has a broken engine block where a piece came off, can blue devil fix this?
    My block is aluminum

    • BlueDevil Pro on May 13, 2019 at 9:51 am

      Jack-

      Thank you for asking about your Subaru Forester. Is the block leaking water/coolant? Please contact our technical support line at 888-863-0426 so that we can get a little better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  43. Jacob Farren on May 28, 2019 at 7:36 pm

    Hi I’ve got a crack on the cylinder wall which has caused my head gasket to go which has been repaired but obviously I haven’t put it back on yet curious on what your thoughts would be and if you product could help fix this?

    • BlueDevil Pro on May 29, 2019 at 8:53 am

      Jacob-

      What are the symptoms you are experiencing with the cylinder wall crack? Please contact our technical support line at 888-863-0426 so that we can get a little better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  44. CHANTELLE ROCHE on June 2, 2019 at 6:02 pm

    1996 Ford F150 crack in lower engine block. Where do I put the Radiator/Block Sealer to seal the crack. Thanks!

    • BlueDevil Pro on June 3, 2019 at 11:32 am

      Chantelle-

      Thank you for asking about your Ford F-150. The BlueDevil Radiator & Block Sealer should be added in through the radiator cap.

      Thank you!

      -BDP

  45. Frank on June 30, 2019 at 11:02 am

    My engine is leaking from right underneath the last pulley on the bottom of the engine. Not sure what it’s called but it’s the biggest pulley on the Block. I’ve known for a little bit of time that my engine has been running a bit hotter than usual. Just a few days ago my serpentine belt was literally melted onto the pulley. I thought I was losing antifreeze from the upper hose as I was seeing it splashed everywhere so I went out and bought a hose and new clamps only to realize that I was leaking from underneath. I also thought it could be the water pump but I had changed that within the last year so I’m not too sure that that is the case. Based on this info could you tell me whether or not I have a cracked block?

    • BlueDevil Pro on July 1, 2019 at 1:29 pm

      Frank-

      Based on your description, even though you just had it replaced within the last year, the water pump might be the location of the leak. In some vehicle models, the water pump is actually driven by the serpentine belt, so a serpentine belt that has malfunctioned, would also cause the water pump to malfunction.

      Hope this helps!

      -BDP

  46. ashutosh on July 5, 2019 at 5:01 pm

    Hi, coolant is leaking from my car, i checked its leaking from engine. i think there is a crack on engine. so can your product fix this problem?
    If yes, from where i can buy it ?

    • BlueDevil Pro on July 8, 2019 at 9:15 am

      Ashutosh-

      How quickly are you losing coolant and where are you located? Please contact our technical support line at 888-863-0426 so that we can get a little better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  47. Lee Cummins on July 12, 2019 at 12:28 pm

    Hi. I have a 2009 ford galaxy. I’ve had the head gasket replaced and head skimmed and pressure tested. I’ve changed the water pump and checked for leaks in the egr cooler. I believe I have a cracked block as there is pressure building in the expansion bottle and the safety cap is blowing water out as it releases the pressure but only at high speeds. I’m wondering if your product will have a chance to fix this issue? And how do I get delivery to Ireland

    Thank you in advance

    Lee

    • BlueDevil Pro on July 12, 2019 at 3:43 pm

      Lee-

      Thank you for asking about your Ford Galaxy. Based on your description, it does sound like you are getting combustion/exhaust gases blowing into the cooling system and creating excess pressure. We recommend applying 16 ounces of BlueDevil Head Gasket Sealer. Given that you have already used a different additive, we recommend chemically flushing the cooling system prior to adding BlueDevil. To give yourself the best overall chance of BlueDevil working successfully is to remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the lowest compression reading. If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull. Leave the plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly.
      You may order the product directly at the following website for delivery to Ireland, https://4x4bitz.ie/shop?keywords=bluedevil&olsPage=search .

      Thank you!

      -BDP

  48. Joseph Marshall on August 18, 2019 at 5:23 pm

    Hi, I have 2006 Ford Mustang, it recently overheated due to a clear leak in the radiator. Upon replacing the radiator with a brand new one it seems like there is constant dripping of coolant under the engine block while the car is running. Which product do you reccomend would fix this?

    • BlueDevil Pro on August 19, 2019 at 10:47 am

      Joseph-

      Thank you for asking about your Ford Mustang. Based on your description, you would be a good candidate for the BlueDevil Radiator & Block Sealer.

      Thank you!

      -BDP

  49. Scott Horn on August 19, 2019 at 3:30 pm

    I just replaced my radiator and thermostat in my 1998 Oldsmobile Intrigue because my radiator had 3 holes in it and my thermostat wasn’t opening after i replaced the radiator. I ran my car around the block and the temp gauge shot straight up. I pulled back in and opened the hood. The coolant hose was pressurised, the thermostat was open but water was bubbling up from the top of the engune block just behind the throttle lever and just behind the thermostat. And i still have a bunch of payments left to make on the car. What can i do without blowing all of my money?

    • BlueDevil Pro on August 20, 2019 at 9:10 am

      Scott-

      Thank you for asking about your Oldsmobile Intrigue. From the sounds of it, you may be getting combustion/exhaust gases pumping back into the cooling system. You can use a “Block Dye Tester” to confirm whether or not that is the case.
      BlueDevil Head Gasket Sealer will still work if your vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure. To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the low compression reading. If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull. Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly. Be sure to follow the guidelines for the proper amount to use based on the size of your cooling system.

      Thank you!

      -BDP

  50. Eoin O'Sullivan on October 10, 2019 at 8:52 am

    Hello,

    My mechanic has confirmed that my 2014 Honda Accord IDtec 2.2lt has a cracked cylinder block , crack at cylinder 2.
    He has recommended that the engine is replaced.

    Do you have a solution or recommendation of a product I can try to fix this issue?
    My engine code is N22B2

    • BlueDevil Pro on October 10, 2019 at 12:32 pm

      Eoin-

      Thank you for asking about your Honda Accord. Are you saying that the block is cracked and coolant is leaking to the ground or that coolant is leaking into cylinder #2? What are the symptoms the vehicle is having? Please contact our technical support line at 888-863-0426 so that we can get a little better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  51. matt hummel on December 9, 2019 at 1:50 pm

    Hi, I have a hairline crack on My bmw e92 m3 engine block. what product can I use?

    • BlueDevil Pro on December 10, 2019 at 9:17 am

      Matt-

      The BlueDevil Radiator & Block Sealer would be the recommended product for the hairline crack on the block of your BMW. Feel free to contact our technical support line at 888-863-0426 with any other questions.

      Thank you!

      -BDP

  52. John on March 26, 2020 at 2:37 am

    I have a Peugeot 405 and the cracked block leaks even before the engine starts,can this sealer help in that case. How can I get the product in Kenya

    • BlueDevil Pro on March 26, 2020 at 9:48 am

      John-

      Thank you for asking about your Peugeot 405. How much coolant are you losing when the engine is off? Please contact our technical support line at 888-863-0426 so that we can get a little better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  53. Ramon De Leon on June 9, 2020 at 5:07 am

    My Ford Ranger was newly overhaul and after putting water on the radiator it leaks heavily between the transmission housing and the engine block. We decided to open and removed the cylinder head and poured water on the water jacket holes, and the result is the same. Any chance this product can sealed the possible cracked on the engine block?
    Thank you for your kind advise.

    Mon

    • BlueDevil Pro on June 9, 2020 at 9:31 am

      Ramon-

      Thank you for asking about your Ford Ranger. Unfortunately you may be losing water a little too quickly for the BlueDevil to be successful. The product is more intended for leaks that are seeping or lightly dripping. Based on your description, you may lose the product before it gets a chance to work properly. A hard part repair may be your best option.

      Thank you!

      -BDP

  54. Xolani on June 28, 2020 at 6:02 am

    Hi I have a mazda3231979 it has a oil leak on the block under a oil the hole is about 2cm to 7cm so can blue development fix it I’m in south Africa. Is it available in SA Spares.

    • BlueDevil Pro on June 29, 2020 at 10:38 am

      Xolani-

      Thank you for asking about your Mazda. Unfortunately, we do not manufacture a product for the type of leak you’ve described. The BlueDevil Oil Stop Leak would be intended to treat rubber seals/gaskets. The only remedy may be to have the hard part repair.

      Thank you!

      -BDP

  55. david tengdin on July 13, 2020 at 3:53 pm

    My Mercruiser inboard / outboard 2.6L engine developed a cracked block when my son ran it with the drive tipped up too high. When he put it down, water rushed in to the intake and the sudden gush on a hot block cracked it. As the system is an open system designed for coolant from fresh water lakes, is there a way to get this product in to the system so it can seal up the block?

    • BlueDevil Pro on July 14, 2020 at 8:31 am

      David-

      The key of the BlueDevil working is that you are able to circulate the same water for the recommended 50 minute idle; on a marine engine you could use a bucket or barrel to accomplish this; it would be best to use 3 – 4 gallons of water. The other necessity is that the water will heat to at least 150 degrees during that run.

      Thank you!

      -BDP

  56. louise on October 27, 2020 at 8:54 am

    good day

    i have a citroen DS3 and i have water filling up from the bottom of my block into my number 2 cylinder? any ideas on a product that can repair it.

    warm regards

    Louise

    • BlueDevil Pro on October 27, 2020 at 9:17 am

      Louise-

      Is the vehicle overheating at all? Have you noticed a bubbling/boiling over in the cooling system? It is possible that you are getting combustion/exhaust gases pumping back into the cooling system. You can use a “Block Dye Tester” to confirm whether or not that is the case.
      BlueDevil Head Gasket Sealer will still work if your vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure. To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak (#2 cylinder). If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull. Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly. Be sure to follow the guidelines for the proper amount to use based on the size of your cooling system.

      Thank you!

      -BDP

  57. Tony Leto on February 7, 2021 at 3:43 am

    I have a 2004 Ford Explorer 6 cylinder with a cracked block. Can you add BlueDevil to the reservoir I have no radiator cap? Should I change my oil afterwards?

    • BlueDevil Pro on February 8, 2021 at 9:46 am

      Tony-

      Thank you for asking about your Ford Explorer. If your vehicle only has a reservoir/overflow rather than a radiator cap, instead of pouring BlueDevil through the reservoir/overflow, with the car off and engine cold you should disconnect the top radiator hose and add the product there; do not pour it into the reservoir. It may be added into the hose or the opening on the radiator. Once BlueDevil has been added, reconnect the hose and start the idle from that point.
      If you are getting water/coolant into the engine oil, we recommend changing the oil before and after the BlueDevil process.

      Thank you!

      -BDP

  58. Vincent on June 17, 2021 at 9:27 pm

    I have a mercruiser 3.7 (which is basically a ford 460) inboard/outboard. Oil is milky white – no visible crack in block and compression is 170,165,165,170 (so was told this is good). Not sure if there is some internal damage or maybe gaskets. This motor runs seemingly well and does not over heat. Any chance this product might work to keep the coolant / oil from mixing? This motor is a closed cooling system so it has coolant and not just freshwater.

    • BlueDevil Pro on June 18, 2021 at 8:29 am

      Vincent-

      Unfortunately, water/coolant mixing in with the engine oil would be a tell-tale sign of a blown head gasket. The BlueDevil Head Gasket Sealer is safe and compatible to use on your MerCruiser. You would want to change the oil before and after the BlueDevil procedure.

      Thank you!

      -BDP

  59. Sonja on September 24, 2021 at 2:36 pm

    Can this be used on an inboard diesel boat motor? (Volvo Penta) — How would the directions differ for application?
    *Boat engine is freshwater cooled only, no coolant. Presents same symptoms as Vincent, however block is very difficult to view. Water is leaking externally from engine…not clear if issue is blown head or cracked block. Can you use both products in this situation?

    • BlueDevil Pro on September 24, 2021 at 3:34 pm

      Sonja-

      Yes, the BlueDevil Head Gasket Sealer can be used on your inboard diesel motor. The key of the BlueDevil working is that you are able to circulate the same water for the recommended 50 minute idle; on a marine engine you could use a bucket or barrel to accomplish this; it would be best to use 3 – 4 gallons of water. The other necessity is that the engine will heat up to at least 150 degrees during the run. Feel free to contact our technical support line at 888-863-0426 with any other questions.

      Thank you!

      -BDP

  60. Nika on January 4, 2023 at 6:10 pm

    I have a 2010 Infiniti G37 and my engine block is cracked and coolant is dripping out will your product seal the crack?

    • BlueDevil Pro on January 5, 2023 at 8:34 am

      Nika-

      Based on your description, the BlueDevil Radiator & Block Sealer would be able to seal the block leak on your Infiniti G37. Feel free to contact our technical support team at 888-863-0426 with any other questions.

      Thank you!

      -BDP

Leave a Reply





Related Articles

Search Blog

Subscribe

Blog Categories