Fixing a Blown Head Gasket

#driveyourlife

blown head gasketFixing a blown head gasket can be a huge job.  It’s such a big job that often times it can be cost prohibitive either from a budget standpoint, or because the vehicle isn’t worth as much as the repair job costs.  A blown head gasket is also the kind of problem that if you continue driving with it can end up causing more damage raising the repair bills.

The head gasket in your vehicle is the gasket in between the 2 largest pieces of your motor, the cylinder head, and the engine block.  The engine block contains the crankshaft and pistons and the cylinder head contains the valve train.  When these two pieces are bolted together, they form the combustion chamber above the piston.  There are also oil and coolant passages that travel between the cylinder head and engine block through the head gasket.

The head gasket is responsible for sealing all of these cooling and oil passages as well as the combustion chamber make sure oil stays in the lubrication system, water stays in the cooling system, and combustion gases stay in the cylinder above the piston.

A blown head gasket is simply a head gasket that has started allowing one or more of these fluids or gases into a space they shouldn’t be.  The combustion chamber is where the temperature gradients are the most extreme and the pressures are the highest so more often than not, this is where a leak will form.

You’ll notice you have a blown head gasket in your vehicle due to the consequences of coolant, oil, or combustion gases being in the wrong place.  You may see bubbles in your radiator or coolant reservoir as combustion gases are leaking into your cooling system.  You may also notice white smoke from your tailpipe as coolant leaks into your combustion chamber and is burned.  Lastly, you may find white milky substance in your oil as coolant leaks into your oiling system.

If you notice any of these symptoms or otherwise suspect you have a blown head gasket, you can check for sure using a few different methods.  First, some auto parts stores sell test kids that can chemically check for combustion gases in your engine coolant which would confirm you have a blown head gasket.  You can also try checking the compression in the cylinders in your car.  If you find one cylinder with very low compression it could indicate you have a head gasket leak into that cylinder, but it may also indicate you have bad piston rings in that cylinder.  Lastly, if you have all the symptoms listed above at the same time, it’s a pretty safe bet you have a blown head gasket.

cylinder head gasketReplacing a blown head gasket is such a hard job because you have to separate the cylinder head from the engine block.  This step in itself does not take very long, but to get there, it requires the removal of a lot of other components.  You have to remove things like the intake and exhaust manifold, the alternator and power steering pump, any wiring going to or across the cylinder head, fuel lines and sometimes the time belt or chain.  Also, if you don’t reinstall everything perfectly, you can quickly cause catastrophic damage to your engine.

The good news is there is a way to fix your blown head gasket without all the work and without even removing the old gasket!  BlueDevil Pour-N-Go Head Gasket Sealer can seal the leak in your head gasket quickly and easily without removing your old head Gasket.  BlueDevil Pour-N-Go Head Gasket Sealer is a chemical sealing agent that will form a chemical weld at the leak keeping your coolant and combustion chamber separate.

For more information about BlueDevil Pour-N-Go Head Gasket Sealer, visit our product information page by clicking on the banner below!
BlueDevil Pour-N-Go Head Gasket Sealer
You can also purchase BlueDevil Pour-N-Go Head Gasket Sealer at any of our partnering local auto parts stores like:

  • AutoZone
  • Advance Auto Parts
  • Bennett Auto Supply
  • CarQuest Auto parts
  • NAPA Auto Parts
  • O’Reilly Auto Parts
  • Pep Boys
  • Fast Track
  • Bumper to Bumper Auto Parts Specialists
  • S&E Quick Lube Distributer
  • DYK Automotive

 

Pictures Provided By:

blown_head_gasket.jpg – By Stocksnapper – Licensed by Thinkstock Photos – Original Link
cylinder_head.jpg – By Evgeniy_Bibikov – Licensed by Thinkstock Photos – Original Link

BlueDevil Products can be found on Amazon.com or at AutoZone, Advance Auto Parts, O’Reilly Auto Parts, NAPA, and other major auto parts retailers.

35 responses to "Fixing a Blown Head Gasket"

35 Comments

  1. Devon on June 2, 2016 at 5:07 pm

    Hi I have a 1999 Mazda millena and I think I have a head gasket leak because every time I add water to radiater and fill it up white smoke/vapor comes out a little and more when I rev it up a little but if I start it up the next day with no water there no smoke ….and it over heats a lot ….and I all ready took out the thermostat should I get the blue devil 32 ounce and use half for my v6 or should I just use the poor and go …and if I use the poor and go would I need to add thermostat first …

    • BlueDevil Pro on June 9, 2016 at 10:26 am

      Devon-

      Thank you for asking about your Mazda Millena. You may use either Head Gasket Sealer. The “Pour N Go” (16 oz./white label) is a less concentrated formula that does not require the removal of the thermostat or a flush of the cooling system prior to use. Whereas the “Mechanic Approved” (32 oz./yellow label) requires both the removal of thermostat and a flush before applying the product; the 32 ounce is the more concentrated formula.
      The product with the yellow label will give you best overall results as long as you can remove the thermostat and flush the system and fill it with water prior to use. However, if the thermostat is difficult to remove or you would rather not then you can always go with the “Pour N Go”.

      Thank you!

      -BDP

    • Curtis on September 17, 2016 at 8:39 pm

      What if your engine won’t start but will turn over?

      • BlueDevil Pro on September 19, 2016 at 11:37 am

        Curtis-

        The vehicle must be able to start and run for a consistent 50 minute idle in order for BlueDevil Head Gasket Sealer to have a chance at working as it is intended.

        Thank you!

        -BDP

  2. Norbert sitnik on June 2, 2016 at 8:29 pm

    How cold should the engine be?Does the engine need to be the same as the air temp?

    • BlueDevil Pro on June 3, 2016 at 9:05 am

      Norbert-

      Form the last time the engine was run you should wait at least 2 hours for it to cool down.

      Thank you!

      -BDP

    • BlueDevil Pro on June 3, 2016 at 9:19 am

      Norbert-

      In terms of using the BlueDevil Head Gasket Sealer, we recommend at least 2 hours of a cool down from when the vehicle was last run. That would be cold enough to start the process. Feel free to contact our technical support line at 888-863-0426 with any other questions.

      Thank you!

      -BDP

  3. Joseph on July 30, 2016 at 2:23 pm

    I have a 2001 Cadillac DeVille Northstar engine when I use the 32-ounce Blue Devil it won’t idle for 50 minutes without overheating how can I go about is there a bypass on the heater coil or the heater core

    • BlueDevil Pro on August 2, 2016 at 10:51 am

      Joseph-

      Please contact us at 888-863-0426 so that we may discuss your Cadillac and the best way to apply BlueDevil Head Gasket Sealer.

      Thank you!

      -BDP

    • Juan Nelson on September 28, 2017 at 12:18 am

      I have a 02 DeVille dhs . I checked my oil and on the Oil stick the oil was moca colored and my coolant was empty , the car is not producing white smoke
      But the oil and antifreeze is mixing , will the Blue Devil pour n go fix my problem ??

      • BlueDevil Pro on September 28, 2017 at 8:50 am

        Juan-

        Thank you for asking about your Cadillac Deville DHS. Based on your description, we recommend using the BlueDevil Head Gasket Sealer (http://store.gobdp.com/head-gasket-sealer-38386/). The BlueDevil Pour-N-Go Head Gasket Sealer is intended for use in 4 or 6 cylinder engines, which your Northstar engine is a V-8. Feel free to contact our technical support line at 888-863-0426 with any other questions.

        Thank you!

        -BDP

  4. Kara Sylve on September 28, 2016 at 9:40 pm

    I have a 2005 Pontiac Grand Prix my car was running hot a lot I changed the water pump it worked fa one day n it was still running hot I had a crack in my radiator it ran hot again so I change the radiator n the thermostat n it’s still running hot the antifreeze it’s bubbling in the overflow jug n plus the temperature is still going up I think I blew a head gasket can I use this product will it solve my problem I dnt have any water leaking out my oil isn’t milky it’s just keeping a high temperature

    • BlueDevil Pro on September 29, 2016 at 2:02 pm

      Kara-

      Thank you for asking about your Pontiac Grand Prix. We recommend using BlueDevil Head Gasket Sealer (http://store.gobdp.com/head-gasket-sealer-38386/). It sounds like the vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure.  To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the low compression reading.  If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull.  Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly.  Be sure to follow the guidelines for the proper amount to use based on the size of your cooling system.

      Thank you!

      -BDP

    • Eric on March 21, 2018 at 3:31 pm

      I have a96 dodge ram a freeze plug popped out when I was driving I replaced the plug and filled it with antifreeze now it’s running rough and blowing white smoke out of exhaust and overheating top hose is getting hot and hard will blue devil gasket sealer help me with my problem

      • BlueDevil Pro on March 21, 2018 at 3:46 pm

        Eric-

        Thank you for asking about your Dodge Ram. It is possible that you are getting combustion/exhaust gases pumping back into the cooling system. You can use a “Block Dye Tester” to confirm whether or not that is the case.
        BlueDevil Head Gasket Sealer will still work if your vehicle is getting combustion/exhaust gases blowing into the cooling system and creating pressure. To give yourself the best overall chance of BlueDevil working successfully, in addition to the directions, you should remove the spark plug from the cylinder with the leak; this will be the spark plug from the cylinder with the low compression reading. If you are not sure which one that is, you may pull all of the spark plugs and will notice one will have a white-crystal-like substance on it and/or may look dirty; this is the plug you should pull. Leave that plug out for the 50 minute idle in order to relieve the pressure from building up and thus allowing the product to seal properly. Be sure to follow the guidelines for the proper amount to use based on the size of your cooling system.

        Thank you!

        -BDP

  5. Guillermo Feliciano on October 2, 2016 at 8:59 am

    My Ford Escape 2008 was overheated two weeks ago. The investment need it to repair the truck was to high. A mechanic talk to me about products that could help with my problem. I made a research through the web and analyse my options. I found Bluedevil and read about it. Also, check YouTube to look what others have done in my situation and follow there example. Bluedevil deliever there promise and help in my situation. Has past two weeks and the truck have no engine problems so far. I can believe yet this really works. Thanks Bluedevil.

    • BlueDevil Pro on October 4, 2016 at 9:59 am

      Guillermo-

      We are happy to hear of the success you have had with the BlueDevil Head Gasket Sealer. Once the product seals, it creates a permanent seal, so you should be good to go at this point.

      Thank you!

      -BDP

  6. Juventino Lucas on May 5, 2017 at 11:47 pm

    I have a Nissan Titan 2008 when I started the engine I got white smoke from the exhaust. But I’m not sure if I have a damaged head gasket. What do you recommend me to do?

    • BlueDevil Pro on May 8, 2017 at 10:24 am

      Juventino-

      Thank you for asking about your Nissan Titan. Is the vehicle overheating at all? Are you noticing a loss of water/coolant? Please contact our technical support line at 888-863-0426 so that we can get a better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

      • Juventino Lucas on May 8, 2017 at 7:37 pm

        Everything in the car is normal. The only thing that worries me is the smoke coming out of the exhaust

        • BlueDevil Pro on May 9, 2017 at 9:24 am

          Juventino-

          Is the smoke coming out of the exhaust consistently or just on start up? You may want to bring the vehicle to a certified ASE mechanic for a proper diagnosis.

          Thank you

          -BDP

          • Juventino licas ventino lucas on May 9, 2017 at 1:24 pm

            Only smoke comes out when I start the vehicle. The smoke is a little thick and in a couple of minutes it disappears and no more



          • BlueDevil Pro on May 9, 2017 at 2:51 pm

            Juventino-

            Have you noticed any loss of coolant or symptoms outside of the smoking? Please contact our tech support team at 888-863-0426 so that we may discuss your vehicle and make the proper recommendations.

            Thank you!

            -BDP



  7. Fidelis on May 30, 2017 at 9:55 am

    I’m Riding On a Polo 6 , The Car Started Overheated about 5Months Back , And I Realised The Water Pump Was Leaking, So I Replaced The Water Pump and the Leaking Stopped But The Car Still Overheats .. Oil Deep Stick Always Comes Out With a Milky Coffee Like Colour .. so From All The Symptoms I’ve Discovered I Suspect That It Has Blown a Head Gasket .. I’ve already tried to remove The Thermostat But Still , And There is a Terrible Sound Knocking When I Start The Engine .. it does Idle , but It Doesn’t Last About 50min Idling Without Overheating , and whenever I Pour Water , It Disappears but I Think its probably the drops and steam that come out of The Exhaust hence It has no visible Leaks Anywhere Else .. the Oil has changed Colour Thus the deep stick Always Comes out with a Milky coffee thick Oil, so there are chances that there is a combination of oil and water along The circulation .. I really need your Help on What step must I take .. can any of these product rescue my car from Dying or any of your technician Assist me or getting it perfectly repaired ?

    • BlueDevil Pro on June 2, 2017 at 12:34 pm

      Fidelis-

      Thank you for asking about your Polo 6. Based on your description, you are most definitely dealing with the symptoms of a blown head gasket. The knocking sound in the engine you are hearing is more than likely a sign of water being in the oil and making its way to your engine bearings. Unfortunately, it sounds like you may be losing water a little too quickly for the BlueDevil Head Gasket Sealer to be affective. If the vehicle is unable to idle 50 minutes without overheating and you are losing more than about a quart of water in that 50 minutes, then the leak you have would be a little too extreme for the product. A hard part repair may be your best option.

      Hope this helps!

      -BDP

  8. Denise on June 3, 2017 at 9:35 am

    I have a Dodge Grand Caravan and blown head. I used the blue devil treatment and coolant. Will the blue devil work? Or do I need another treatment?

    • BlueDevil Pro on June 5, 2017 at 10:14 am

      Denise-

      Thank you for asking about your Dodge Grand Caravan. Please contact our technical support line at 888-863-0426 so that we can get a better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  9. Raven on September 15, 2017 at 11:38 am

    Hi. I have a 2008 Chevy HHR that started overheating Wednesday. I put water in it and it was good overnight. THursday, it started overheating again and my mechanic checked it out… The heater hose was busted. He fixed that. Found a radiator issue… But then he said the gasket is blown and he JUST put this engine in my car back in May… Will this product possibly help fix my issue? Or is it too late?

    • BlueDevil Pro on September 15, 2017 at 1:41 pm

      Raven-

      Thank you for asking about your Chevy HHR. As long as the vehicle will maintain idle for a full 50 minutes, without overheating or stalling out, and you are not losing more than about a quart of water/coolant during that 50 minutes, you would be a great candidate for the BlueDevil Head Gasket Sealer (http://store.gobdp.com/head-gasket-sealer-38386/). Feel free to contact our technical support line at 888-863-0426 with any other questions.

      Thank you!

      -BDP

  10. Michelle on October 8, 2017 at 6:04 pm

    I have a 2006 Sukuzi Forenza and was told the head gasket was blown. How much would it generally cost to fix at a shop?

    • BlueDevil Pro on October 9, 2017 at 10:09 am

      Michelle-

      Thank you for asking about your Suzuki Forenza. Depending on your location, head gasket replacement could cost anywhere from $1,000 – $1,500. Depending on the severity of your symptoms or water/coolant leak, you may be a candidate for the BlueDevil Head Gasket Sealer. Please contact our technical support line at 888-863-0426 so that we can get a better understanding of the vehicle’s condition and be able to make any appropriate recommendations.

      Thank you!

      -BDP

  11. Will nunz on June 25, 2019 at 6:50 pm

    I have a 2010 Jeep Grand Cherokee Laredo and the other day I noticed white puff coming from exhaust on start up so I checked my coolant and it was tarnish brown kinda sludge will blue devil help? I just bought this car help please!!

    • BD Auto Pro on June 25, 2019 at 9:26 pm

      Will,

      Thanks for your question about your 2010 Jeep Grand Cherokee. You often get white smoke from your exhaust shortly after startup due to moisture in your exhaust. This is especially true if the weather is cooler or humid. This small amount of moisture from your exhaust will go away as your vehicle warms up unless you have a blown head gasket so it would be worth watching for other indications of a blown head gasket. In the meantime it would be smart to flush your cooling system to get rid of the old brown sludge, clean your system and refill it with fresh coolant. You can use BlueDevil Radiator Flush to get that taken care of.

      Thanks again for your question!
      -BD Auto Pro

  12. John on October 28, 2020 at 7:32 pm

    whats the recommendation for oil in the coolant in a 1999 Mitsubishi Montero with a 6 cylinder engine?

    • BlueDevil Pro on October 29, 2020 at 8:14 am

      John-

      Unfortunately, we do not manufacture a product intended to stop oil from getting into the coolant. Replacing the head gasket may be your best option in this instance.

      Thank you!

      -BDP

Leave a Reply





Related Articles

Search Blog

Subscribe

Blog Categories